کابلهای سامانه ذخیرهسازی انرژی برای اتصال بانک باتری، اینورتر و تابلوهای توزیع در نیروگاههای ذخیرهساز به کار میروند. جریان بالای پیوسته، فضای بسته و حساسیت ایمنی این سامانهها ایجاب میکند که کابل هم ظرفیت جریاندهی مناسب و هم رفتار کمدود بدون هالوژن هنگام حریق داشته باشد.
در مورد H01N2-D EN 50525-2-81 Welding، روکش لاستیکی انعطاف بالا در دمای پایین را حفظ میکند.
EN 50525-2-81, EN 60228, HD 22.6, VDE 0282-6, BS 638 Part 4 Flame Retardant according to IEC/EN 60332-1-2
Separator :PET (Polyester Tape)
Sheath :Rubber compound
Sheath Colour : Black Red
Voltage Rating : 100V
Temperature Rating : Fixed: -40°C to +85°C Flexed: -20°C to +85°C
Minimum Bending Radius : Fixed: 6 x overall diameter
| NO. OF CORES | NOMINAL CROSS SECTIONAL AREA mm² | NOMINAL THICKNESS OF INSULATION mm | NOMINAL WEIGHT kg/km | ||
|---|---|---|---|---|---|
| 1 | 10 | 2 | 146 | ||
| 1 | 16 | 2 | 204 | ||
| 1 | 25 | 2 | 290 | ||
| 1 | 35 | 2 | 384 | ||
| 1 | 50 | 2.2 | 535 | ||
| 1 | 70 | 2.4 | 716 | ||
| 1 | 95 | 2.6 | 943 | ||
| 1 | 120 | 2.8 | 1,235 | ||
| 1 | 150 | 3 | 1,556 | ||
| CONDUCTORS | ||||
|---|---|---|---|---|
| Flexible Copper Conductors for Single Core Cables | ||||
| NOMINAL CROSS SECTIONAL AREA mm² | MAXIMUM RESISTANCE OF CONDUCTOR AT 20ºC ohms/km | |||
| 10 | 1.91 | |||
| 16 | 1.21 | |||
| 25 | 0.78 | |||
| 35 | 0.55 | |||
| 50 | 0.39 | |||
| 70 | 0.27 | |||
| 95 | 0.21 | |||
| 120 | 0.16 | |||
| 150 | 0.13 | |||
| NOMINAL CROSS SECTIONAL AREA mm² | CURRENT RATING FOR SINGLE CYCLE OPERATION OVER A MAXIMUM PERIOD OF 5 MINUTES Amps | ||||
|---|---|---|---|---|---|
| 0.85 | 0.35 | ||||
| 10 | 100 | 103 | 122 | ||
| 16 | 135 | 145 | 230 | ||
| 25 | 180 | 195 | 300 | ||
| 35 | 225 | 245 | 375 | ||
| 50 | 285 | 305 | 480 | ||
| 70 | 355 | 385 | 600 | ||
| 95 | 430 | 470 | 730 | ||
| 120 | 500 | 540 | 850 | ||
| 150 | 580 | 630 | 980 | ||
| Ambient Air Temperature: 25°C Maximum Conductor Temperature: 85°C | |
|---|---|
| Ambient Air Temperature: 25°C Maximum Conductor Temperature: 85°C | |
| Duty Cycle and Current Carrying Capacity The current carrying capacity of a welding cable depends on the length of the duty cycle. The duty cycle is the length of time during which a loaded current passes through the cable over an operation period of 5 minutes, expressed as a percentage of that period. For example, if the current is flowing for the whole 5 minutes the duty cycle is 100%, and if the current is flowing for 1 minute the duty cycle is 20%. As conductor temperature varies according to the time in use as well as current, ratings shown are given as a guide. The permissible loading of the cable for duty cycles other than those shown in the table can be calculated using the following formula: I = I100 x √100/F Where: I : is the maximum permissible loading current for the required duty cycle. I100 : is the maximum permissible loading current for a duty cycle of 100%. F : is the required duty cycle calculated as a percentage of the 5 minute operation period. Typical guidance values for different welding processes are as follows: Fully automatic welding 100% Semi-automatic welding 65 - 85% Manual Welding 30 - 60% Very infrequent or occasional welding 20% |